vtx 1300 Shop manual - VTXOA
 
LinkBack Thread Tools
post #1 of 6 (permalink) Old 11-26-2012, 08:38 PM Thread Starter
Senior Member
 
Join Date: Jul 2009
Location: Proctor, WV westpennsyltucky
Posts: 6,203
vtx 1300 Shop manual

ive been reading through the shop manual and honda missed something important. the forget to mention the torque value for the cam holder cap bolts. i have a 2003-2007 manual if you have a different manual can you check page 8-21 to see if the torque value is listed

thanks




"Government, even in its best state, is but a necessary evil; in its worst state, an intolerable one." Thomas Paine
Where is our government!
Greg Riddle is offline  
Sponsored Links
Advertisement
 
post #2 of 6 (permalink) Old 11-26-2012, 08:46 PM Thread Starter
Senior Member
 
Join Date: Jul 2009
Location: Proctor, WV westpennsyltucky
Posts: 6,203
i just checked the 2003-2004 service manual and its the same no torque value




"Government, even in its best state, is but a necessary evil; in its worst state, an intolerable one." Thomas Paine
Where is our government!
Greg Riddle is offline  
post #3 of 6 (permalink) Old 11-26-2012, 10:11 PM
Senior Member
 
Hans&Feet's Avatar
 
Join Date: Jun 2005
Location: Conyers/McDonough, GA
Posts: 7,850
Garage
You skipped right past it.... Check that bearing surface for clearance! 8-7 of 03-04 svc manual

2005 1300c Red, Mustang seat, HK 2.5 straights. Leds for safety-front & back. 175,035 miles of smiles
Hans&Feet is offline  
post #4 of 6 (permalink) Old 11-27-2012, 04:52 AM Thread Starter
Senior Member
 
Join Date: Jul 2009
Location: Proctor, WV westpennsyltucky
Posts: 6,203
i did catch the torque setting you posted but that is for checking bearing clearance. is it the same for actual torque during use




"Government, even in its best state, is but a necessary evil; in its worst state, an intolerable one." Thomas Paine
Where is our government!
Greg Riddle is offline  
post #5 of 6 (permalink) Old 11-27-2012, 08:33 AM
Senior Member
 
Hans&Feet's Avatar
 
Join Date: Jun 2005
Location: Conyers/McDonough, GA
Posts: 7,850
Garage
Yes! The actual operating condition torque values are required to correctly determine
bearing clearance.
03-04 SM 1-10 has a torque chart, general fasteners on the left side, specialized fasteners on the right.
The torque values should all be on a chart on the first few pages, not just a few for the fasteners used in that chapter/section.
http://i1185.photobucket.com/albums/...bolttorque.jpg

2005 1300c Red, Mustang seat, HK 2.5 straights. Leds for safety-front & back. 175,035 miles of smiles
Hans&Feet is offline  
post #6 of 6 (permalink) Old 11-27-2012, 08:40 AM
Senior Member
 
Join Date: Feb 2011
Location: Orlando
Posts: 180
Ive got the 03-07 manual and dont see a value other than the 9 lbf-ft during the plastigauge bit. Exploded view on pg 8-2 doesnt even have it (nor is it in the values on the next page under the chart) Making a guess of it, and only a guess, it would seem the torque used to measure oil clearance would be the torque value for normal operation.

[SIGPIC][/SIGPIC]2007 VTX1300R
FlRob is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the VTXOA forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome