Search:

Larry,
Search for threads that i started and i think you will find a drawing of the bracket that needs to be fabricated to mount the Fury Pipes.
Other than that rear mount, a couple of bolts is...

I am sure Glen's product is Great! You can make one from your own needle and a little stuff you may already have


http://www.vtxoa.com/forums/showthread.php?326825-10-Min-AF-Screw

I purchased a Goldwing in June. Since then the X has only been ridden 3 times. I don't want her to sit in the garage and not get ridden, so i am going to sell her. The bike is Red, has 11k ish miles...

You can take a piece of 1/2" all thread, two nuts and a washer and make a tool to remove the races as well. Really isn't that hard, and you can tighten the ALL Balls a bit tighter than the old Junk...

Rear wheel bearing is bad, removed the wheel and the inside center fell out of the bearing, leaving the outer race in the wheel. How do i get ahold of the race to remove it?

You might try a couple of more pounds of air and see if it still seems to wonder at slow speeds. Finding the right air pressure is important to getting the FEEL correct.

I love my General Grabber

The biggest issue with brake fluid is that it absorbs water. Then eventually the water causes corrosion inside the system, and can boil in the brake wheel cylinder. you just need a short hose from...

Welcome to the jungle!
Valves as mentioned are not that difficult to do. I would recommend looking to see if the PAIR valve has been removed before attempting the Valves. IF it is still there, buy...

My wife wants me to purchase another bike! (Goldwing) for the long trips! Goods news is she wants me to keep the VTX!:mrgreen:
Any you guys know anything about a Goldwing? Looking right now at the...

Your Rear-end (butt) will thank you. Smoother ride the MT. :mrgreen:

I used AIRSOFT pellets in my darkside, i just had them in a baggie ready, after the tire was on the rim, unseated, i just poured them in. Put about 4 oz in there and ride it like you stole it.

Here is a good instruction on how to work on the carb. --http://www.vtxoa.com/forums/showthread.php?206510-1300-Carburator-Scar-Mod-A-F-Mix-amp-Idle-Adj-Fuel-Pump-bypass

Jets can be picked up or...

I used a carpenters NAIL Puller, it hooked them and removed them in seconds.

BTW- you can buy the crush gaskets at Auotzone- Advanced Auto - O-Rielly's -Napa ( your local parts store)

I posted this a while back, can't seem to find it now? I like doing things myself, and saving $ where i can.

You can make your own AF adjuster with:

1. Aprox 6" 1/8" Steel or SST cable
2...

If you replaced the neck bearings with stock replacement bearings, you will have the same problem. Replace them with ALL Balls, tighten them up until there is slight resistance turning the bars. I am...

I have the General Grabber 205/70/15 rear - Avon Rode Rider AM26 front (universal tire)
Have about 4k on them now. Love them!

I used a set of 1800 "F" Risers. Worked great for me. Found them on the 1800 classifieds for about $30

I agree with Greg. If you want to enlarge the existing main jet, drill it. .078 (5/64") is real close to a #200 main jet. 2.05mm is real close to a 205 main, 2.1mm is 210 main, 2.15 is 215 you get...

Here is some good reading about batteries. They can be damaged by Not charging, by Overcharging with to high voltage, by charging to fast with large amps, poor maintenance, improper storage and...

I worked in a battery shop for about two years. We supplied 7 states with batteries, believe me, they can be bad right off the shelf. They can also last for about 5 years if properly maintained. If...

With the parts you already have why spend $70 for another kit. Sounds like the bottom end is close #58 pilot is OK

I ill get blasted for this but for about $3 you can zero in on the main jet by:
...

Purchased a 220 CCA battery at Advance auto ONline and picked it up at the store for $67 by using VISA as a promo code during checkout $30 off

...

I agree Donut - You are going to drwon that thing with fuel - it will foul plugs at 2.5 pretty quickly

Just my opioion. Let us know how it works for ya.

My thoughts are that MOST of us could...

check the two plugs under the tank, make sure they are plugged tightly and not loose

I just switched mine back to the #58 from a #60 pilot -- bike actually has better feel of the pants torque and runs smoother at slower speeds, plugs were fouling a bit with the 60 jet - (Doug- i...