VTXOA - View Single Post - Custom LED Fog/Brights/Auxiliary DIY-ish
View Single Post
post #2 of (permalink) Old 01-26-2018, 01:23 AM Thread Starter
Dethlore
Senior Member
 
Dethlore's Avatar
 
Join Date: Aug 2012
Location: Utah
Posts: 157
Step 1: READ EVERYTHING FIRST! You never know if you want to do something a little bit differently!

Step2: Get your parts!
All boxed up!
Out of the box.
Out of the packaging.

Step 3: Dry run mate the parts together.

Step 4: Polish everything you want to shine! I used Mother's Aluminum Polish and a shop rag.


Step 5: Next, only if needed, drill the center hole of the led star and heatsink for the 4 conductor cable to fit through. A crescent wrench or a vise would be best to hold the star in place.


Step 6: Solder the wires onto the star terminals. Make note of which wires you have going to each positive and negative pad.


Step 7: Use a hacksaw to cut the threaded rod into sections just long enough to thread into the heatsink block, and go all the way through the p-clamp with enough room for a locking nut.


Step 8: Mix a small amount of thermal epoxy and apply it to one end of the threaded rod. Thread this into the heatsink block without coming out the other side. Wipe any beading or excess away from where the rod enters the block.


Step 9: For the best possible mate, grind off one point of the copper female threaded fitting. Grind this point down until you have the best fit into the heatsink block.
Marked points to grind.
Dry run to check fit.

Step 10: Mix a small amount of arctic silver epoxy 1:1 and epoxy the copper fittings onto the heatsink blocks. I positioned mine with the hexagon points toward the rear of the heatsink to protect the LED housing itself, but positioning is completely up to you. MAKE SURE that when you epoxy this, that you don’t have any excess coming forward from the copper fitting. The LED housing needs to be able to thread down against the fitting for best thermal conduction.


Step 11: Drill a hole in the copper caps just large enough for the cable to fit through (sorry no picture). Cut 2 pieces of copper pipe just enough to fit the street elbow into the cap. Assemble the copper assembly as you see in the previous picture. You can epoxy these, solder, or duct tape if you want… I want to chrome plate them in the future…

Step 12: Solder the cable ends to the 4 pin connectors in a similar method of my wiring diagram… and remember to use heatshrink tubing to protect those connections! Yes, I’m using computer molex connectors… but you should use marine grade waterproof connectors.


Step 13: If you haven’t done so, remove the gas tank from your bike. Prepare the power cables with inline fuses (or use your own fuse block) and use the terminal connectors on the end in case you need to pull the circuit apart ever in the future. Use the diagram included in my parts list.

*Positive connections with in-line fuse blocks.
Connectors for the switches and to ground.

Step 14: Mount your custom LED Lights! Use cable ties to secure the cable along your crash guard bars, or wherever you've decided to mount them. I used chromed stainless steel cable ties.

You can barely see the cable ties!

Step 15: Fit the drivers between the top two frame bars and use electrical tape (or whatever you have around) to mount them securely. Connect the (+) and (-) cables to the switches, and the drivers to the switches (not the battery yet!!)


Step 16: In my case, the switches are mounted in the left neck cover, but you can have them anywhere… Finish mounting the switches.


Step 17: Connect the power cables to the battery – I connected the positive to the battery, and the negative to a nearby grounding bolt.
At this point, your lights are mounted! If you haven’t done so, properly align them so you’re not blinding oncoming traffic and so you get maximum visibility.
There is no need to remove the front forks as is shown in the pictures – I just happened to be rebuilding the forks, brake calipers, and adding an LED headlight at the same time!
The finished project with amber lights and white lights with separate switches. If I have them both on at the same time, I get a slightly warmer color white.






Please let me know what you think! I appreciate the questions and comments!


2005 VTX1300C - Darkside Michelin Defender 205/70/15 - Kuryakyn Hypercharger - Mustang Seats - 2up Switchblade - Custom Front Fender - Kuryakyn Highway Bars - Clayton Mod - PAIR Removed - Mobil M110 - Rotella Triple T 15W40 - UV Engine LEDs - Custom LED-Supply Running Lights

Last edited by Dethlore; 01-26-2018 at 11:10 AM.
Dethlore is offline  
 
 
For the best viewing experience please update your browser to Google Chrome